CHARACTERISTICS
I. Cold rolled products made of low carbon non-alloyed structural steel are used for the production of flat or cold-formed structural elements. Their application is determined by the minimum value of the yield point, or by the tensile strength.
II. Cold rolled products made of fine-grained, atmospheric corrosion
resistant structural steel are mostly used in the building industry and for various constructions.
Improved resistance is due to the surface layer of oxides of alloying elements.
Coils
wide strips with a rolled width of 600 mm and more, supplied in coils
Strips
cut from wide strips, width less than 600 mm, supplied in coils
Sheets
sheets cut from wide strips supplied in sheets
CHEMICAL COMPOSITION
|
Grades according to DIN 1623:2009 and tech. standards USSK |
Heat analysis in % | |||||
|---|---|---|---|---|---|---|
| C max. | Mn max. | Si max. | P max. | S max. | N max. | |
| KOSIL 200 S | 0,16 | 0,60 | 0,030 | 0,025 | 0,020 | - |
| S215G | 0,18 | 1,50 | - | 0,030 | 0,025 | 0,0105 |
| KOSIL 215 S | 0,16 | 0,80 | 0,030 | 0,025 | 0,020 | - |
| S245G | 0,20 | 1,60 | - | 0,030 | 0,025 | - |
| S325G | 0,20 | 1,60 | 0,55 | 0,030 | 0,025 | - |
|
Grades according to TN USSK 10025-5 |
Heat analysis in % | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| C max. | Mn | Si | P | S max. | Al min. | Cu | Ni max. | Cr | |
| KONOX 315CR | 0,12 | 0,20 - 0,55 | 0,25 - 0,55 | 0,07 - 0,15 | 0,015 | 0,02 | 0,25 - 0,60 | 0,65 | 0,50 - 1,20 |
MECHANICAL PROPERTIES
|
Grades according to |
Rp0,2 [MPa] min. | Rm [MPa] |
A [%] min. Lo = 80 mm |
Bend test | |
|---|---|---|---|---|---|
| α | D | ||||
| KOSIL 200 S | 200 | 310 - 430 | 22 | 180° | 0,5a |
| S215G | 215 | 360 - 510 | 20 | - | - |
| KOSIL 215 S | 215 | 360 - 470 | 20 | 180° | 0,5a |
| S245G | 245 | 430 - 580 | 18 | - | - |
| S325G | 325 | 510 - 680 | 16 | - | - |
|
Grades according to
TN USSK 10025-5 |
Rp0,2 [MPa] min. | Rm [MPa] |
A [%] min. L0 = 80 mm |
Bend test | |
|---|---|---|---|---|---|
| α | D | ||||
| KONOX 315CR | 315 | 450 | 23 | 180° | 0,5a |
for KOSIL 200 S, KOSIL 215 S, S215G and corresponding
| Nominal thickness [mm] | Width [mm] | ||||
|---|---|---|---|---|---|
| 750 | 1 105 | 1 265 | 1 425 | 1 500 | |
| 0,400 - 0,449 | |||||
| 0,450 - 0,749 | |||||
| 0,750 - 1,149 | |||||
| 1,150 - 2,000 | |||||
for S245G, S325G, KONOX 315CR and corresponding
| Nominal thickness [mm] | Width [mm] | ||||||
|---|---|---|---|---|---|---|---|
| 750 | 1 015 | 1 085 | 1 200 | 1 275 | 1 325 | ||
| 0,550 - 0,649 | |||||||
| 0,650 - 0,949 | |||||||
| 0,950 - 1,249 | |||||||
| 1,250 - 1,749 | |||||||
| 1,750 - 2,000 | |||||||
The width of 700 - 749 mm at the thickness of 0,80 - 2,00 mm is the subject to prior agreement
DIMENSIONS OF SHEETS
| Thickness [mm] | Length [mm] |
|---|---|
| 0,40 - 1,00 | 1 000 - 3 000 |
| 1,01 - 2,00 | 1 000 - 3 000 |
NOTE: above 3 000 mm we produce in cooperation
DIMENSIONS OF COILS AND SLIT COILS [MM]
| Thickness | Inner diameter | Outer diameter | Coil | Slit coil | ||
|---|---|---|---|---|---|---|
| Width | Weight | Width | Weight | |||
| 0,40 - 1,30 | approx. 500 or 600 | max. 1 800 | 750 - 1 050 | 3 - 15 kg.mm-1 of width | 21 - 600 | max. 15 000 kg |
| 1,31 - 2,00 | approx. 600 | 750 - 1 500 | 2 - 17 kg.mm-1 of width | 21 - 600 | max. 15 000 kg | |
NOTE: thickness is graded by 0,01 mm
- THICKNESS TOLERANCES IN ACCORDANCE WITH EN 10131, Re < 260 MPa
-
Nominal thickness Normal tolerances at width Reduced tolerances at width ≤ 1 200 > 1 200 ≤ 1 500 ≤ 1 200 > 1 200 ≤ 1 500 > 0,40 ≤ 0,60 ± 0,03 ± 0,04 ± 0,025 ± 0,030 > 0,60 ≤ 0,80 ± 0,04 ± 0,05 ± 0,030 ± 0,035 > 0.80 ≤ 1,00 ± 0,05 ± 0,06 ± 0,035 ± 0,040 > 1,00 ≤ 1,20 ± 0,06 ± 0,07 ± 0,040 ± 0,050 > 1,20 ≤ 1,60 ± 0,08 ± 0,09 ± 0,050 ± 0,060 > 1,60 ≤ 2,00 ± 0,10 ± 0,11 ± 0,060 ± 0,070 NOTE: reduced tolerances are subject to prior agreement
- THICKNESS TOLERANCES IN ACCORDANCE WITH EN 10131, 260 ≤ Re < 340 MPa
-
Nominal thickness Normal tolerances at width Reduced tolerances at width ≤ 1 200 > 1 200 ≤ 1 500 ≤ 1 200 > 1 200 ≤ 1 500 > 0,40 ≤ 0,60 ± 0,04 ± 0,05 ± 0,030 ± 0,035 > 0,60 ≤ 0,80 ± 0,05 ± 0,06 ± 0,035 ± 0,040 > 0.80 ≤ 1,00 ± 0,06 ± 0,07 ± 0,040 ± 0,050 > 1,00 ≤ 1,20 ± 0,07 ± 0,08 ± 0,050 ± 0,060 > 1,20 ≤ 1,60 ± 0,09 ± 0,11 ± 0,060 ± 0,070 > 1,60 ≤ 2,00 ± 0,12 ± 0,13 ± 0,070 ± 0,080 NOTE: reduced tolerances are subject to prior agreement
- SHEET FLATNESS TOLERANCES IN ACCORDANCE WITH EN 10131, Re < 260 MPa
-
Nominal width Normal tolerances at thickness Reduced tolerances at thickness < 0,70 ≥ 0,70 < 1,20 ≥ 1,20 < 0,70 ≥ 0,70 < 1,20 ≥ 1,20 ≥ 600 < 1 200 10 8 7 5 4 3 ≥ 1 200 < 1 500 12 10 8 6 5 4 ≥ 1 500 17 15 13 8 7 6 NOTE: reduced tolerances are subject to prior agreement
- SHEET FLATNESS TOLERANCES IN ACCORDANCE WITH EN 10131, 260 ≤ Re < 340 MPa
-
Nominal width Normal tolerances at thickness Reduced tolerances at thickness < 0,70 ≥ 0,70 < 1,20 ≥ 1,20 < 0,70 ≥ 0,70 < 1,20 ≥ 1,20 ≥ 600 < 1 200 13 10 8 8 6 5 ≥ 1 200 < 1 500 15 13 11 9 8 6 ≥ 1 500 20 19 17 12 10 9 NOTE: r educed tolerances are subject to prior agreement
DOWNLOAD
logistics INFORMATION
We offer flexible product delivery with multiple options for packaging and methods of transportation.
CONTACT US PERSONALLY
Milan Beličák
Director Sales Czech Republic and Slovakia
Milan Malík
Director Sales Poland
+421 556 734 654
+421 903 627 471
mmaliksk.uss.com
Eva Širilová
Director Sales West Europe
+421 556 734 016
+421 917 656 761
esirillovask.uss.com
Ján Rohár
Director Sales South & East Europe and Export
+421 556 734 596
+421 903 616 433
jroharsk.uss.com
Dušan Dzurovčin
Key Account Manager Austria
+421 556 734 538
+421 917 731 813
ddzurovcinsk.uss.com